Tekla Structures 2017i SR7

TSAC-1458 Rebar coupler and end anchor components have been changed so that they set the phase of the coupler/end anchor to be the same as the phase of the related primary reinforcement bar. Note that if you change the phase of the coupler/end anchor manually afterwards, this manual change will be overridden whenever the coupler/end anchor component gets updated.
TSAC-2452 In Rebar hole, when Rounding type on the Parameters tab is set to Round by table and Hole type on the Advanced tab is set to Part cut or Bolt hole + part cut, if the maximum rebar diameter value in the table is smaller than the rebar diameter defined in the rebar properties, Tekla Structures displayes a warning message: Rebar diameter from table is smaller than the rebar diameter from model.
TSAC-2418 In Turnbuckle connection (126), the main and the secondary part are now correctly fitted regardless their selection order.
TSAC-2310 In Welded beam column (31), you can now turn on or off the weld preparation creation in the welds dialog box.
TSAC-2309 In Welded column with stiffeners (128), you can now turn on or off the weld preparation creation in the welds dialog box.
TSAC-2230 In Clip angle (141), weld 5 between the stiffener and the main part is now created correctly.
TSAC-2199 In Full depth S (185), you can now define the tab plate end cut on the Plates tab.
TSAC-1540 In Column with stiffeners W (182), the stiffener weld preparation now works properly.
TSAC-1459 In Shear plate tube column (189), the plate chamfer size now correctly follows the value defined in the component dialog box.
TSAC-946 In Welded beam to beam (123), the bottom flange notch size is now correctly applied.
TSAC-796 In Bent plate (151), the distances of bolts from the edge of the plate are now correctly applied.
TTSD-22194 DWG export file name does not have revision info added if the revision info is not present in the format string.
TTSD-20216 With the IFC2x3 export using the Coordination and Steel Fabrication model view definition, the beams and columns that have a fitting plane at both ends are shorter than in the model. The error does not occur when line cuts are used instead or only one fitting is used. This has now been fixed.
TTSD-21637 Radius symbols in rebar pull-out pictures in reports were sometimes incorrectly drawn after opening drawing, but correct after refreshing the report. This has now been fixed.
TTSD-20722 Support for showing numbers greater than 2^31 was added.
TTSD-23449 There were problems opening a drawing containing failing bolt solids. This has now been fixed and drawings can be opened even if there is a failing bolt solid.
TTSD-15941 Drawing section views are now resized to include all view contents, for example, when an associative note is added so that text part is positioned outside the section view
TSAC-2400 Rebar group dimensioning: The order of mark content elements is now correct in all use cases. The fix also applies to extra marks.
TSAC-2375 Pattern line editor saves the default color correctly in the created .clp file, so the pattern line color can be modified.
TSAC-1746 Rebar group dimensioning: Each of the CC distances is now shown correctly in the dimension line
TTSD-23046 Previously, if Tekla Structures crashed or if the Tekla Structures process was somehow forced to exit during write out, this could result in missing drawing files. This has now been fixed.
TTSD-22652 In Tekla Model Sharing, read in performance has been improved.
TTSD-22212 In Tekla Model Sharing, canceling the start sharing was not possible during packet creation. This has now been fixed.
TTSD-21567 In Tekla Model Sharing, profiles with a .clb file as a subtype were not previously shared correctly. This has now been fixed.
TTSD-22524 Previously, when the Ortho tool was active, the snapping distances were incorrectly rounded. This has now been fixed.
TTSD-21482 Previously, if you left Tekla Structures idle for a while, in some cases Tekla Structures could freeze or crash. This has now been improved.
TTSD-21481 Previously, selecting two bolts and right-clicking caused Tekla Structures to crash. This happened when the first part you had selected was a cast-in-place part. This has now been fixed.
TTSD-17887 If you need to reset pour unit contents and relations defined using the Calculate pour units command and/or the Add to pour unit command, you can now use the following commands in Quick Launch:
- Reset all pour unit relations
- Reset all manually assigned pour unit relations
- Reset all pour unit relations except manual assignments
The first two commands have a dialog box where you confirm the command. This is because you cannot undo the commands.
TTSD-22656 Previously, when a user had created an analysis model in a multi-user model and another user saved the model, this new analysis model was not visible for either user in the Analysis & Design Model dialog box. This has now been fixed.
TTSD-22080 In a Tekla Model Sharing model, when you read in changes that included an analysis model, and an autosaved model was created after read in and the model then reopened without saving, the analysis model could sometimes be lost. This has now been fixed.
TSAC-2485 The Dimensioning Rule Properties dialog box had many texts that were not translated but showed the string ID albl_… This has now been fixed.
TTSD-23434 In Tekla Model Sharing models, using Organizer or some other .NET tools could previously cause errors at write out when using the Project viewer role. This has now been fixed.
TSAC-2514 Export EliPlan file (68): Cuts created at diagonally cut slabs no longer affect the calculation of L1 and L2 values.
TSAC-2450 BVBS Export: The user-defined bending roll diameter can now be controlled with the BVBS_BENDING_ROLL UDA
TSAC-2446 BVBS Export: When multiple segments of rebar are in 0-degree bendings then is exported as the continuous straight section.
TSAC-2390 Export Unitechnik (79): Production thicknesses of double wall shells are now calculated so that the 1st shell thickness reports sub-assembly thickness including braced girders, and the 2nd shell reports complete cast unit thickness regardless of the chosen dialog box option. This is to ensure that the production thickness values comply with the curing chamber slot maximum height.