SOFiSTiK 2020 SP 2020-4 Build 850 for AutoCAD 2020

AQB

Bugfixes
- CTRL DESV +4 Option has been deactivated by accident. (171759)
- Eigen stress from creep and shrinkage for reinforcements was to high for NSTR analysis. (170638)
- The effect of the longitudinal reinforcements for the shear design of hollow sections has been to large. (169633)

AQUA

Bugfixes
- Sometimes the non existing material 134 was used for shear reinforcements. (171832,171841)
- Some values (eg. Az) of FEM cross sections were sometimes calculated inaccurately. (167192)
- Sometimes incorrect shear cuts were created when the cut hit an arc created by a tangent point (TP).

ASE

Bugfixes
- Cable analysis with inner cable sagging extended on formfinding with GRP FACS > 1.0 (170338)
- Time step analysis storage extreme values with STEP-LCSM: corresponding values corrected in case usingLCST CONT. (171129)
- In global z variable quad temperature load (SOFILOAD QUAD DTYX DPZ) did not run - corrected. (171539)

BEMESS

Bugfixes
- Punching foundation slabs: reduction of soil pressure due to supportforce of central node corrected. (171088)
- Fatigue concrete: with NSTR LC14 0 now the old 2018-check according EN 1992-1-1 6.8.7 (6.77) will be done. (171138)
- Fatigue reinforcement: accuracy improved, especially if a low stress range shall be reached. (171722)
- Punching force could be too high on design of earthquake superposition loadcases - corrected. (170805)
Other Issues
- Multi layer reinforcement design extended for tendons

CSM

Other Issues
- CSM Design: Maxima superposition extended for use of MAXIMA tracing TRAC.
- CSM Design: Maxima superposition for Result Sets RSET improved - can be switched off with CTRL RSET 0.

DECREATOR

Features
- All items that are intersected by a design section are now marked in the Sectional Intersection chapter of the output report file. A corresponding legend is also available.
Bugfixes
- DECREATOR crash due to a reference of undefined cross section is fixed. (171126)
- Transformation of forces from a volume-element model to a Design Element, whose coordinates do not match that of the global, are corrected. (171706)
- The axis position of a design element, in case of eccentric beam elements having eccentric cross-sections, is corrected. This concerns only the visualization of design elements in Wingraf.
- Thicknesses of intersected orthotropic quad elements is corrected.

DYNA

Features
- Modal superposition: Support reactions from ASE eigenvalue analysis can now be considered for modal superposition (-> EXTR U); In this case, for existing line boundary elements, also related bedding reactions are computed.

ELLA

Features
- Search for initial solution with variable length of loading improved. (170558)
Bugfixes
- Performance for brake loadings of LM71 enhanced. (171223)
- Problems with RSET and eliminated kinematic constraints resolved.

HASE

Other Issues
- Service pack release.

SOFINI

Features
- SS EN1992-2004: Revision of the defaults with new version BFS 2019:1 EKS 11 (National Annexes Sweden for buildings), modification of the action combination according to equation 6.10a Revision of the defaults with new version TSFS 2018_57 (National Annexes Sweden for bridges) additional adaption of the values for Sweden in EN1993-2005 and EN 1994-2004

MAXIMA

MAXIMA

Bugfixes
- Fixed problem in storing results on given X position of BEAM elements. (171834)
Other Issues
- Minor improvements of TRAC.

Result Viewer

Features
- It is possible to display whether a reinforcement point is inside of a non effective area.
- Now there is a filter for stations at structural lines to get start and end.
- Table-Assistant: Lists with filtered extreme values of internal forces at structural lines can now be created according to various criteria.

SOFILOAD

Bugfixes
- LM3 3600/200/200 had no spare distance. (171325)
- Tolerances for LINE loadings on small elements in large systems improved. (170902)

SOFIMSHC

Bugfixes
- Fixed issue when subdividing structural lines with an exlicitly given number of elements.
- Fixed issue in meshing structural areas with complex openings.

SSD

General

Bugfixes
- Materials: Modified material definitions are always retained, even if values were subsequently changed in the dialog of the boxed value. In this case, the dialog of the boxed values brings a message. (171293)
Calculation of Concrete Columns
Bugfixes
- Column: In the task "Column System" with multi-storey columns, a load at the start of the beam was sometimes not recognized correctly. (171831)
- Column: In the task "Column design", all columns of the main system were not found, which had a zero crossing between the column top and column bottom (Z=0 in the global coordinate system). (171222)

Teddy

Bugfixes
- The window "Search and Replace" did not appear correctly after repeated closing with the Close-X. (169879)

WinGraf

Bugfixes
- It sometimes took a long time to read the required cross section data. (171830)
- Sometimes utilisation levels of beams were not displayed. (171127)
- The group number and cuts direction of QUAD cuts was not saved in database with command "Save DB cut". (171511)

- SOFiCAD and SOFiPLUS 2020 require AutoCAD 2020.
- SOFiSTiK Analysis + Design requires Revit 2020.
- The Rhinoceros Interface requires Rhino 6.
- SOFiPLUS-X does not require AutoCAD.
- The databases (cdb) created by the FEA programs are not compatible with those of the full version and vice versa.
- Our products are tested and released for Windows 8.1 (64bit) and 10.