Dlubal Software 2023 (rev.23012023)

Update Report No. 03441 RFEM 5 5-31-01 | 01/23/2023
- Reset of trial licenses - they can be reactivated once only
- Adaptations in the panel regarding the display of surface thicknesses of surfaces of the Laminate stiffness type
- Adaptations concerning the deactivation of surfaces in the load case options - if line hinges are assigned on these surfaces, they are now also deactivated
- Adaptations in the export of the DXF format regarding the export of arcs and circular lines as well as the numbering of the objects
- Adaptations in the GH interface regarding the export of surfaces with curved boundary lines - they were sometimes exported twice
- Adaptations concerning the transfer of the model to RWIND Simulation if the model contains null members
- Adaptations concerning the conversion of intersection lines into normal lines
Update Report No. 03440 RSTAB 8 8-31-01 | 01/23/2023
- Reset of trial licenses - they can be reactivated once only
- Adaptations in the Stiffness Diagram nonlinearity of member hinges regarding the input of positive values in the negative diagram area
- Adaptations concerning the transfer of the model to RWIND Simulation if the model contains null members
Update Report No. 03439 RF-CONCRETE 5-31-01 | 01/23/2023
- Adaptations concerning the displayed values on surfaces - the values could sometimes show massive deviations when compared with the underlying results
- Improved the calculation of the required shear reinforcement of surfaces. When minimum shear reinforcement was activated, it was always output as the statically required reinforcement area
- Adaptations in the design of the required longitudinal reinforcement for the serviceability limit state of circular cross sections
Update Report No. 03438 CONCRETE 8-31-01 | 01/23/2023
- Adaptations in the design of the required longitudinal reinforcement for the serviceability limit state of circular cross sections
Update Report No. 03437 RF-STEEL EC3 5-31-01 | 01/23/2023
- Adaptations concerning the selection of section deformation in the settings for rotational restraints
- Adaptations concerning the consideration of the rotational restraint and the shear panel in fire protection stability checks if no ultimate limit state design is carried out at the same time
Update Report No. 03436 STEEL EC3 8-31-01 | 01/23/2023
- Adaptations concerning the selection of section deformation in the settings for rotational restraints
- Adaptations concerning the consideration of the rotational restraint and the shear panel in fire protection stability checks if no ultimate limit state design is carried out at the same time
Update Report No. 03435 RF-DYNAM Pro - Natural Vibrations 5-31-01 | 01/23/2023
- Adaptations concerning the presentation of masses in Tab. 5.7 Effective Modal Mass Factors - only zero values were displayed in some cases
Update Report No. 03434 CRANEWAY 8-31-01 | 01/23/2023
- Adaptations in fatigue design for the lower flange regarding the applied vertical load
Update Report No. 03433 RF-LAMINATE 5-31-01 | 01/23/2023
- Update of compositions from the company Piveteau Bois
- Adaptations in the printout report in table 2.2 when displaying stresses on selected surfaces
Update Report No. 03432 RF-GLASS 5-31-01 | 01/23/2023
- Adaptations in the result table of maximum displacements regarding the limit uZ values

The structural FEA software RFEM for analysis and design of plates, walls, shells, solids, and frame structures is a powerful program for various tasks of modern civil engineering. This program forms the basis of a modular software system: RFEM determines internal forces, deformations, and support reactions of general plate structures with or without member and solid elements. The program version RFEM 5 provides a wide range of useful features and options for efficient and user-friendly work on your structural analysis projects.
With RSTAB , Dlubal's structural analysis program for spatial frameworks (German: Räumliche STABwerke), you've got a powerful tool to cope with a variety of different tasks in civil engi-neering. The program represents the basis for Dlubal's analysis software composed of various design modules: RSTAB determines internal forces, deformations and support reactions of general framework structures. Then, the results can be used in add-on modules for specific de-signs and other analyses. The program version RSTAB 8 offers you several useful features and options emphasizing user-friendliness and easy program handling when working on structural analysis projects.
COMPOSITE-BEAM automatically analyzes the resulting internal forces and carries out all relevant verification according to following the standards. The results are displayed in the spreadsheet masks. They are sorted by the required analysis standards and thus enable an easy orientation. The user`s control over the input as well as the interpretation of the results is facilitated through 3D visualization. All graphics can be edited and transferred to the Printout Report. The Dlubal COMPOSITE-BEAM program performs design of composite beams according to: ENV 1994‑1‑1:1992‑10. The program is based on bidirectional communication between RSTAB and the add‑on modules.
CRANEWAY expands DLUBAL'S product range by the crane runway girder design. Thanks to the well-known user-friendliness of Dlubal programs, you can carry out even complicated analyses according to EN 1993-6, DIN 4132, and DIN 18800 in an easy and comprehensible way.The crane runway girder is specified in the CRANEWAY module. Based on the defined loadings, the program creates load cases that are combined in load positions. Each load position results in three load combinations. Each load combination is calculated with three loading levels in order to determine the internal forces for the general stress design, the deformation analysis, or the fatigue design. The internal forces are determined according to the second-order analy-sis for warping torsion. With these calculated internal forces, CRANEWAY provides the appro-priate analyses according to EN 1993-6, DIN 4132, or DIN 18800.
PLATE-BUCKLING is pow-erful tool for designing plate-like structural components. Country-specific regulations are tak-en into account by National Annexes (NA). In addition to the parameters included in the pro-gram, you can define your own limit values or create new National Annexes.PLATE-BUCKLING can be used as a stand-alone program or as an add-on module in RSTAB or RFEM. In the add-on module, you can import design-relevant input data and internal forces from the current RSTAB or RFEM model. Finally, the design process can be documented in the global printout report, from input data to design. The European standard Eurocode 3 (EN 1993-1- 5:2010-12 + NA 2010-12) describes design and construction of plate-like structural steel components used in the member states of the Euro-pean Union.
The SHAPE-MASSIVE cross-section properties software runs independently of the main program. The program determines the section properties of any thick-walled cross-section and calculates the stresses. Furthermore, it is possible to perform the reinforced concrete design according to Eurocode 2 and other standards.
RX-TIMBER is a DLUBAL program family that meets specific demands in timber engineering. With the programs included in the RX-TIMBER package you can analyze various structural components (glued-laminated beams, continuous beams, timber columns, coupled purlins, frames, bracing, and roofs) in the ultimate limit state, the serviceability limit state, and fire resistance design according to Eurocode 5. The governing result combinations are created automatically with the add-on module RF-COMBI that is integrated in RX-TIMBER. All of the RX-TIMBER programs are able to perform the ultimate and the serviceability limit state design.
SHAPE-THIN is a professional, user-friendly program for the analysis and design of thin-walled cross-sections. The stand-alone module is based on the effective program concept of the RSTAB and RFEM software family. For example, the user is able to exchange different sectional elements between individual SHAPE files with drag & drop. At the same time, the internal forces and moments of member elements can be taken from any.

COMPOSITE.BEAM.8.31.01
CRANEWAY.8.31.01
PLATE.BUCKLING.8.31.01
SHAPE.MASSIVE.6.81.01
RFEM.5.31.01
RSTAB.8.31.01
RX.TIMBER.2.31.01
SHAPE.THIN.9.10.01